THE MINISTRY of Defense (MoD) has been issued with a Crown Censure by the Health and Safety Executive (HSE) after an employee was shot during a training exercise.
In January 2019 an employee of the Ministry of Defense suffered severe injuries as a result of being shot with live ammunition during a training exercise where blank ammunition should have been used. This put both employees and persons not in the employment of Ministry of Defense, at risk.
The incident has had severe life changing consequences for the injured employee. Following their medical discharge, they suffered from PTSD and following the incident had difficulty performing routine tasks such as getting dressed, cooking cleaning and driving. .
By accepting the Crown Censure, the MoD admitted breaching its duty under Section 2(1) and Section 3 (1) of the Health and Safety at Work etc. Act 1974 in that they failed to ensure, so far as was reasonably practicable, the health, safety and welfare at work of its employees, and persons not in their employment, particularly in relation to the risks associated with training exercises.
After the hearing, HSE inspector Stacey Gamwell said, “This was a very serious incident which could have easily resulted in death. Just like any other employer, the MoD has a responsibility to reduce risk to its employees and others who may be affected by its work.
“We recognize military training can be hazardous – but where work of this nature is to be done, that danger should be controlled as much as reasonably practicable.
“An objective of military training is to prepare personnel for potential hazardous situations, but this does not mean the training itself should expose trainees to uncontrolled or inadequately controlled hazards.
“An employer must take all reasonably practicable steps to control the risk to the safety of employees whilst they are at work and others who may be affected by that work. They can do this through suitable and sufficient risk assessment and safe systems of work.”
Thanks to Health and Safety Matters for the original Article : https://www.hsmsearch.com/HSE-issues-MOD-Crown-Censure
Fire Extinguisher Barcode Inspection Software
Fire Extinguisher Barcode Inspection Software system can be used to manage monthly fire extinguisher inspections, annual inspections and 6 year and 12 year inspections and also general fire safety inspections. Allowing Managers to record safety observations while performing facility tours which can improve overall fire safety. A Fire Extinguisher Inspection Software system that can create corrective actions as a result of inspection failures and allocate these corrective active actions to the appropriate persons, with deadlines for resolution will greatly reduce the time, effort and cost of managing NFPA inspections. Implementing a Fire Extinguisher Barcode System, where users scan each fire extinguisher using a Mobile Fire Extinguisher Inspection Software App aids with compliance with NFPA and The joint Commission and other Authorities having Jurisdiction(AHJ’s) within Universities, Colleges, Hospitals, Medical Centers, Manufacturing, Oil and Gas and many other sectors.
Easy to Use – Fire Extinguisher Barcode System
IMEC Inspection Software is an easy to use fire extinguisher barcode system which will schedule, manage, track and report on any type of inspection, including Facility, Equipment, People etc. Use Cases include fire extinguisher barcode system, eyewash stations, emergency showers, equipment or asset inspection system or facilities inspection software. When used as a fire extinguisher barcode system Inspections are performed via the Mobile app which is available on iOS, Android and Windows devices. The user identifies the inspection point by scanning a barcode, or picking from a list based on location. The Mobile App which is part of the fire extinguisher barcode system will then display the list of custom Forms or Checklists. The fire extinguisher barcode system inspections can be performed offline if no internet connection is available.
The IMEC Mobile Safety App can also be used as a Fire Door Inspection App and with the Web based flexible Forms Manager the solution can be used as a Fire Door Inspection Software Solution also. Fire Door Inspection Software is used is large facilities with large quantities of Fire Doors like Hospitals, Universities and also Cruise Ships.
Not Just A Fire Extinguisher Barcode System but a Complete Fire Life Safety Inspection Software Solution
IMEC Inspection Software can be deployed as a full Fire Life Safety Inspection Software solution that can be used to manage an organization’s full range of fire and life safety inspections. The IMEC Fire Life Safety Inspection Software can manage any type of inspection, use cases include Fire Doors, Fire Pumps, Eyewash Stations, Emergency Lights, Emergency Showers, Grease Traps, AED’s and many more. The IMEC Fire Life Safety Inspection Software can manage any type safety equipment or asset inspection. The user identifies the inspection point by scanning a barcode, or picking from a list based on location. The Mobile App will then display the list of custom Forms or Checklists. The solution can be used within Hospitals as a Hospital Inspection Software solution to manage all hospital inspections and Environment of Care Rounds. Hospital Inspection Software makes Daily, Weekly and Monthly Inspections more efficient and accurate. IMEC’s Hospital Inspection Software allows health care and facility managers to monitor the inspections across their entire organization to aid compliance and increase efficiency.
EH&S Inspection Software
IMEC’s EH&S Inspection Software can be used to manage any type of EHS Inspection and allows manager to record safety observations while performing facility tours which can improve overall workplace safety. This EH&S Inspection Software solution that can create corrective actions as a result of inspection failures for inspections performed using the Safety Inspection Software Mobile App. Corrective actions are allocated to the appropriate persons, with deadlines for resolution which will greatly reduce the time, effort and cost of managing compliance inspections. Implementing an EH&S Inspection software solution, where users using the Safety Inspection Software Mobile App can easily perform inspections in the field aids compliance, reduces risk and standardizes the inspection process within your organization.
Asset Inspection Management Software
IMEC’s Asset Inspection Management Software can be used to manage any type of Asset Inspection. This Asset Inspection Management Software solution can create corrective actions as a result of asset inspection failures for inspections. Corrective actions are allocated to the appropriate persons, with deadlines for resolution which will greatly reduce the time, effort and cost of managing compliance inspections. Implementing an Asset Inspection management software solution, where users using a Mobile App can easily perform inspections in the field aids compliance, reduces risk and standardizes the inspection process within your organization.
Lock Out Tag Out Software Solutions
IMEC’s Lock Out Tag Out Software Solutions allow a LOTO procedure to be defined for each piece of equipment that requires LOTO to be managed within the system. Equipment can be managed from both Mobile and Web App. Isolation points for the each piece of equipment are managed, images associated with both the piece of equipment and isolation points can be annotated to include energy source icon, arrows, sequence etc. Lock Out Tag Out Procedures can be authored using the Mobile App with version control and with an approval workflow. Lock Out Tag Out Procedures are executed using the Mobile App on any Smart Phone or Tablet. Lockout Tagout procedures are initiated by the user identifying the piece of equipment by either scanning QR Code or selecting the piece of equipment from a list. A complete history of completed Lockout Tagout Procedures is recorded. The status for the piece of equipment can be updated after LOTO is complete – Locked / Unlocked. An Audit option on the Mobile App allows a procedure to be reviewed without performing LOTO on the piece of equipment. Corrective Actions can be created for any Non-conformances or changes required recorded during the Procedure Review. Data Analytics within the IMEC Lock Out Tag Out Software Solutions provide machine downtime analysis to aid in operational efficiency and investment decisions.
Hazardous Waste Management Software
HazMat T&T is a hazardous waste management software solution designed for Environmental Service Companies and companies who generate a large quantity of hazardous waste. The solution tracks hazardous waste from cradle to grave aiding compliance, providing accurate waste inventory, increasing waste handling efficiency, reducing risk and also helps manage waste costs. HazMat T&T Hazardous Waste Management Software can be deployed in a number of deployment scenarios, from Large Hazardous Waste Generators, tracking their hazardous waste at their site to Environmental Service and Waste Management Companies using it track and manage hazardous waste at transfer and disposal sites.
IMEC Technologies provides Safety Management Software to increase worker safety and aid compliance. IMEC’s Safety Management Software will manage inspections and audits, provides hazard identification, incident reporting, management of corrective and preventative actions from generation to closure. IMEC provides lock out tag out software solutions that will allow users to create lockout tagout procedures using an intuitive Mobile App and Manage Lockout Tagout Procedures, also the Review and Execution of those Lockout Tagout Procedures using the Mobile App. Annual Lockout Tagout Procedures audits are conducted using a Mobile App. The Mobile Inspection App allow users to perform inspections and audits, for example the system can be used as a Fire Extinguisher Barcode Inspection Software system to manage monthly fire extinguisher inspections and general fire safety inspections and also to record safety observations and manage corrective actions, anywhere and anytime. The solution can be used as a fire extinguisher barcode inspection software system or life safety inspection system to aid compliance in Higher Education, Healthcare, Industrial and Commercial Organizations. Benefits from a Fire Extinguisher Barcode System include the elimination of paperwork and reducing the burden of compliance with regulations such as NFPA, The Joint Commission. The Mobile App can also be used as a Fire Door Inspection App and with the flexible Forms Manager the solution can be used as a Fire Door Inspection Software Solution also. Fire Door Inspection Software is used is large facilities with large quantities of Fire Doors like Hospitals, Universities and also Cruise Ships. The Incident Reporting App allows users to easily and quickly report incidents, hazards and near-misses, these are then sent to the appropriate people for action and are managed to closure. Web Apps provide features such as, setup, management, scheduling tools, analysis, reporting and dashboards etc with the ability to report incidents to government bodies such as OSHA and RIDDOR. HazMat T&T is a hazardous waste management software solution designed for Environmental Service Companies and companies who generate a large quantity of hazardous waste. The solution tracks hazardous waste from cradle to grave aiding compliance, providing accurate waste inventory, increasing waste handling efficiency, reducing risk and also helps manage waste costs. HazMat T&T Hazardous Waste Management Software can be deployed in a number of deployment scenarios, from Large Hazardous Waste Generators, tracking their hazardous waste at their site to Environmental Service and Waste Management Companies using it track and manage hazardous waste at transfer and disposal sites. For more information visit our website www.imectechnologies.com